User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            HP 6032A:System Power Supply
DATE:                  07-Feb-96
AUTHOR:                User Contributed
REVISION:              0
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       1
NUMBER OF LINES:       53
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK+                                          X
  1.002  ASK-   R     N              P                            F        W
  1.003  HEAD         ÍÍ INITIAL CONDITIONS ÍÍ
  1.004  DISP         The following test equipment is required:
  1.004  DISP         1. Keithley 179A DTB # 9-78
  1.004  DISP         2. Transistor Devices DLP 50-150-3000A
  1.004  DISP         3. Sensitive Research 50 Amp Shunt DTB # 14-3
  1.005  DISP         Set the UUT front panel controls as follows:
  1.005  DISP         LINE ON/OFF ........................................ OFF
  1.005  DISP         OVP ADJUST .................................... fully CW
  1.006  DISP         Connect the System port 1 to the UUT HP-IB connector.
  1.007  DISP         Remove the UUT rear panel terminal strip cover.
  1.008  DISP         All connections are made to the rear panel
  1.008  DISP         terminal strip.
  1.009  DISP         ÿ Connect the UUT and the 1281 as follows:
  1.009  DISP         ÿ[27][91]1m     6032A        TO        1281[27][91]m
  1.009  DISP         ÿ  OUTPUT  (+S) ÄÄÄÄÄÄÄÄÄÄÄÄ> INPUT-HIGH
  1.009  DISP         ÿ  OUTPUT  (-S) ÄÄÄÄÄÄÄÄÄÄÄÄ> INPUT-LO
  1.010  DISP         Connect UUT AC line cord to Variac (220 VAC/30A).
  1.011  DISP         Monitor 115 AC Volts at one leg of the 220V variac with
  1.011  DISP         the Keithley 179A set to read AC Volts, 200 V range.
  1.012  DISP         Set the variac to 115 VAC.
  1.013  IEEE         [SRQ OFF]
  1.014  DISP         Set the UUT front panel controls as follows:
  1.014  DISP         LINE ON/OFF ......................................... ON
  1.015  IEEE         [D3000]
  1.016  CALL         HP 6032A: Sub 1
  1.017  CALL         HP 6032A: Sub 2
  1.018  IEEE         CLR;
  1.019  HEAD
  1.020  DISP         Set the UUT front panel controls as follows:
  1.020  DISP         LINE ON/OFF ........................................ OFF
  1.021  HEAD         {}
  1.022  DISP         {ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»}
  1.022  DISP         {º THIS COMPLETES THE VERIFICATION º}
  1.022  DISP         {ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ}
  1.023  END
#! T.U.R.s less than 4.00:                  0
#! T.U.R.s estimated using RANGE value:     0
#! T.U.R.s not calculated (ASK- U):         0
#! T.U.R.s not computable at compile time:  7
#! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.